I S P
Cards equipped
with "In-System Programming" CPU.
|
E
D U C A T I O N A L S |
![](../OFFER/i_foto/i_K51AVR2.gif) |
KIT
- K51 AVR
Through K51-AVR
board it is given the chance to have a well-known and documented
hardware, both under a software and a hardware point of view,
to undertake any learning path which, starting form simple experiments,
can improve experience and application complexity, up to being
able to handle, with complete mastery and great competence, the
basic elements of micro-controllers based electronics.
|
3
Type - C P U |
![](../BLOCK/CPU/i_foto/i_gpc323.gif) |
GPC®
323
General Purpose Controller Philips or Atmel
89C51Rxx
|
4
Type - C P U |
![](../BLOCK/CPU/i_foto/i_gpc324.gif) |
GPC®
324
General Purpose Controller Philips or Atmel
89C51Rxx
|
M
Type - C P U |
|
GPC®
R168P
General Purpose Controller Relay; 16 Input, 8 Output.
Philips od Atmel 89C51Rxx 22MHz; 64K
FLASH; RTC + RAM + Lithium battery; 32K RAM; 16 Opto-In; 8 5A
Relay Output; 0,5K Serial EEPROM; 4 8 bit A/D lines; 1
D/A line, 8bit; External INT line, galvanically
coupled; Serial Communication Interface for RS 232: RS
422; RS 485; Current Loop; Built-in Switching
power supply; Housing for Omega Rail.
|
![](../M_TYPE/i_foto/i_gpcT168.gif) |
GPC®
T168P
General Purpose Controller Transistors; 16 Input,
8 Output.
Philips od Atmel 89C51Rxx 22MHz; 64K
FLASH; RTC + RAM + Lithium battery; 32K RAM; 16 Opto-In; 8 Darlington
Output; 0,5K Serial EEPROM; 4 8 bit A/D lines; 1 D/A
line, 8bit; External INT line, galvanically coupled; Serial
Communication Interface for RS 232: RS 422; RS
485; Current Loop; Built-in Switching power
supply; Housing for Omega Rail.
|
grifo® Analog BLOCK - CAN - C P U |
![](../GAB_Type/i_foto/i_gabH844.gif) |
GAB H844
GAB- Housing,
8 Alalog-In, 4 Opto-In, 4 Relay
Housing Analog BLOCK Module witch 8
Analog-In ,4 Opto-In, 4 Relay Outputs; Serial Line
RS232 or TTL, RS422/485, Current Loop;1 I2C
BUS line,
1 Serial Line USB
or CAN; Power Supply.
|
grifo® Mini BLOCK - C P U |
![](../MB_Type/i_foto/i_GMB_HR84.gif) |
GMB HR84
GMB- Housing,
8 Opto-In, 4 Relay
Housing Mini BLOCK Module witch 8
Opto-In and 4 Relay Outputs; Serial Line RS232 or TTL,
RS422/485, Current Loop; 1 I2C BUS line,
1 Serial Line USB or CAN; Power Supply.
|
![](../MB_Type/i_foto/i_GMB_HR168.gif) |
GMB HR168
GMB - Housing,
16 Opto-In, 8 Relay
Housing Mini BLOCK Module witch 16
Opto-In and 8 Relay Outputs; 2 Serial Line RS232 or TTL;
1 Serial Line RS422, RS485, Current Loop; 1 I2C
BUS line,
1 Serial Line USB
or CAN; Power Supply.
|
![](../MB_Type/i_foto/i_GMB_HR244.gif) |
GMB HR246
GMB - Housing,
24 Opto-In, 16 Relay
Mini BLOCK Module witch 24 Opto-In
and 16 Relay Outputs; 2 Serial Line RS232 or TTL; 1 Serial
Line RS422, RS485, Current Loop; 1 I2C
BUS line,
1 Serial Line USB
or CAN; Power Supply.
|
QTP
GPC® Type - C P U |
![](../QG_Type/i_foto/i_qtp12trB.gif) |
QTP 12/R84
QTP 12, 8 Opto-In, 4 Relay
Quick Terminal Panels 12 keys; 1 LED;
Graphic and Alphanumeric Display
20x2; Buzzer; Serial Line RS232, RS422/485, C. Loop; CAN; 8 Opto-in, 4 Relay, Power Supply.
|
![](../QTP/i_foto/i_qtp16Big_LFR.gif) |
QTP 16Big
QTP 16 Big
- 3 Relay
Quick Terminal Panels Big 16 keys; 5
LED; Alphanumeric Display 20x4; 3 Relay; Buzzer; Serial
Line RS232, RS422/485, C. Loop; CAN;
Power Supply.
|
CAN
Type C P U - grifo® Mini Modules - 8 0 5 1 Core |
![](../CAN/i_foto/i_gpcGM1.gif) |
CAN GM Zero
Controller Area Network - grifo® Mini Module Zero
This CAN Mini Module has a 28 pin connector
and it is based on Atmel T89C51CC03 CPU with 64K
FLASH; 2,2K RAM; 2K FLASH for Bootloader; 2K EEPROM; 3 Timers
Counters and 5 Programmable Counter Array channels (for PWM,
watch dog, compare, capture); RTC + 240 Bytes SRAM, backed by
Lithium battery; I2C BUS; 22 TTL I/O lines; 8 A/D 10 bits; RS
232 or TTL; CAN; 2
status LEDs; configuration dip switch; etc.
|
![](../CAN/i_foto/i_gpcGM1.gif) |
CAN GM1
Controller Area Network - grifo® Mini Module 1
This CAN Mini Module has a 28 pin connector
and it is based on Atmel T89C51CC01 CPU with 32K
FLASH; 256 Bytes RAM; 1K ERAM; 2K FLASH for Bootloader; 2K
EEPROM; 3 Timers Counters and 5 Programmable Counter Array channels
(for PWM, watch dog, compare, capture); RTC + 240 Bytes SRAM,
backed by Lithium battery; I2C BUS; 22 TTL I/O lines; 8 A/D 10
bits; RS 232 or TTL; CAN;
2 status LEDs; configuration dip switch; etc.
|
![](../CAN/i_foto/i_200.gif) |
CAN GM2
Controller Area Network - grifo® Mini Module 2
This CAN Mini Module has a 28 pin connector
and it is based on Atmel T89C51CC02 CPU with 16K
FLASH; 256 Bytes RAM; 256 Bytes ERAM; 2K FLASH for Bootloader;
2K EEPROM; 3 Timer Counter and 2 Programmable Counter Array channels
(for PWM, compare, capture); RTC + 240 Bytes SRAM, backed by
Lithium battery; I2C BUS; 18 TTL I/O lines; 6 A/D 10 bit: RS
232 or TTL; CAN; 1 status
LED; configuration dip switch; etc.
|
![](../CAN/i_foto/i_190.gif) |
CAN GMT
Controller Area Network - grifo® Mini Module Test
Low price card usefull for evaluating and test purpose
of 28 pin Mini Modules type CAN GM1, CAN
GM2, etc.. It provides: D9 connectors for a direct
connections to CAN line and
RS 232 line; power supply section with standard connector;
push buttons and LEDs for digital I/O signals management;
prototype area; etc.
|
![](../MM_Type/i_foto/i_ACB_Zero.gif) |
GMM ACB Zero
grifo®
Mini Module AT89C51CC03
This grifo®
Mini Module has a 40 pin connector and it is based
on Atmel AT89C51CC03 CPU with 64K FLASH;
2,2K RAM; 2K FLASH for Bootloader; 2K EEPROM; 64K RAM
External Addressing; 3 Timers Counters and 5 Programmable Counter
Array channels (for PWM, watch dog, compare, capture); 34
TTL I/O lines; 8 A/D 10 bits; RS 232 or TTL; CAN; 2 status LEDs; configuration
dip switch; etc.
|
![](../MM_Type/i_foto/i_518.gif) |
GMM 518 Zero
grifo®
Mini Module AT89C51CC03
This grifo®
Mini Module has a 28 pin connector and it is based
on Atmel AT89C51CC03 CPU with 64K FLASH;
2,2K RAM; 2K FLASH for Bootloader; 2K EEPROM; 3 Timers Counters
and 5 Programmable Counter Array channels (for PWM, watch dog,
compare, capture); 24 TTL I/O lines; 8 A/D 10 bits;
RS 232 or TTL; CAN; 1 status
LED; configuration jumper; etc.
|
![](../SOFT/FOTO/bascom_8051.jpg) |
FREE OF CHARGE
Theoretical/Practical Course
on
|
CAN
grifo® Mini Module - A V R Core |
![](../CAN/i_foto/i_CAN_AVR.gif) |
CAN AVR
Controller Area Network - grifo® Mini Module AVR
grifo®
Mini Module has a 28 pin connector and it is based
on Atmel AT90CAN128 CPU witch 128K FLASH; 4K SRAM;
4K EEPROM; 3 Timer Counter ; 3 PWM; 1 A/D; 24 TTL I/O
lines;1 Comparetor; RTC + 240 Bytes SRAM, backed by Lithium battery;
I2C BUS; Master/Slave SPI; RS 232 or TTL; CAN;
2 status LED; 2 configuration dip switch; etc.
|
![](../CAN/i_foto/i_190.gif) |
CAN GMT
Controller Area Network - grifo® Mini Module Test
Low price card usefull for evaluating and test purpose
of 28 pin Mini Modules type CAN GM1, CAN
GM2, etc.. It provides: D9 connectors for a direct
connections to CAN line and
RS 232 line; power supply section with standard connector;
push buttons and LEDs for digital I/O signals management;
prototype area; etc.
|
![](../PROG/HBI/i_foto/i_AVRISPmkII.jpg) |
AVRISP
MKII
Low-Cost ATMEL ISP Programmer
for Micros AVR.
USB Interface.
|
![wpe1.jpg (4608 bytes)](../SOFT/FOTO/bascom1.jpg) |
FREE OF CHARGE
Theoretical/Practical Course
on
|
CAN
grifo® Mini Module - PICCore |
![](../CAN/i_foto/i_CAN_PIC.gif) |
CANPIC
Controller Area Network - grifo® Mini ModulePIC
grifo®
Mini Module has a 28 pin connector and it is based
on Microchip PIC18F4680 CPU witch 64K FLASH; 4K
SRAM; 1K EEPROM; 3 Timer Counter ; 2 PWM; 5 A/D; 22 TTL
I/O lines;1 Comparetor; RTC + 240 Bytes SRAM, backed by Lithium
battery; I2C BUS; Master/Slave SPI; RS 232 or TTL; CAN;
2 status LED; configuration dip switch; etc.
|
![](../CAN/i_foto/i_190.gif) |
CAN GMT
Controller Area Network - grifo® Mini Module Test
Low price card usefull for evaluating and test purpose
of 28 pin Mini Modules type CAN GM1, CAN
GM2, etc.. It provides: D9 connectors for a direct
connections to CAN line and
RS 232 line; power supply section with standard connector;
push buttons and LEDs for digital I/O signals management;
prototype area; etc.
|
![](../MM_Type/i_foto/i_PG_PIC.gif) |
GMMPIC-PG
grifo®
Mini Module Programmer
Low price card usefull for programmer 28 or
40 pin grifo®
Mini Modules type GMM 876, GMM 4620,
CANPIC, etc. It provides: ZIF 40 pin socket; D9
connectors for a direct connections to RS 232 line; Connectors
RJ12 for MPLAB®;
Connectors 10 pin for a direct connections to MP PIK+; power supply section with
standard connector; 2 LEDs; etc.
|
MM
Type C P U - grifo® Mini Modules - 8 0 5 1 Core |
![](../MM_Type/i_foto/i_ACB_Zero.gif) |
GMM ACB Zero
grifo®
Mini Module AT89C51CC03
This grifo®
Mini Module has a 40 pin connector and it is based
on Atmel AT89C51CC03 CPU with 64K FLASH;
2,2K RAM; 2K FLASH for Bootloader; 2K EEPROM; 64K RAM
External Addressing; 3 Timers Counters and 5 Programmable Counter
Array channels (for PWM, watch dog, compare, capture); 34
TTL I/O lines; 8 A/D 10 bits; RS 232 or TTL; CAN; 2 status LEDs; configuration
dip switch; etc.
|
![](../MM_Type/i_foto/i_1210.gif) |
GMM MSC1210
grifo®
Mini Module MSC1210
grifo®
Mini Module has a 40 pin connector and it is based
on Burr-Brown MSC1210 CPU with 32K FLASH; 1,2K
RAM; 2K FLASH for Bootloader; 64K RAM External Addressing;
32K FLASH/EPROM External Addressing; RTC by Lithium
battery + 64Kb FRAM; 3 Timer Counter; PWM 16 bit; I2C BUS; Master/Slave
SPI Serial Interface; 29 TTL I/O lines; 7/8
A/D 24 bit; 2 RS 232 or TTL; 2 status
LED; etc.
|
![](../MM_Type/i_foto/i_ACB.gif) |
GMM ACB
grifo®
Mini Module AT89C51AC2
This grifo®
Mini Module has a 40 pin connector and it is based
on Atmel AT89C51AC2 CPU with 32K FLASH;
256 Byte RAM;1K ERAM; 2K FLASH for Bootloader; 2K EEPROM; 64K
RAM External Addressing; 32K FLASH/EPROM External
Addressing; 3 Timers Counters and 5 Programmable Counter Array
channels (for PWM, watch dog, compare, capture); 34 TTL I/O
lines; 8 A/D 10 bits; RS 232 or TTL; 2 status LEDs; configuration
dip switch; etc.
|
![](../MM_Type/i_foto/i_F346.gif) |
GMM F346
grifo®
Mini Module C8051F346
grifo®
Mini Module has a 28 pin connector and it is based
on Silicon Laboratories C8051F346 CPU with 64K
FLASH; 4352 Byte RAM; 1K USB FIFO; ICE-Chips; RTC + 64Kb
FRAM; I2C BUS; 4 Timer Counter; 22 TTL I/O lines;
18 A/D 10 bit; Comparator; Built-in Temperature sensor;
RS 232 or TTL; USB; 1
status LED; configuration jumper; etc.
|
![](../MM_Type/i_foto/i_518.gif) |
GMM 518 Zero
grifo®
Mini Module AT89C51CC03
This grifo®
Mini Module has a 28 pin connector and it is based
on Atmel AT89C51CC03 CPU with 64K FLASH;
2,2K RAM; 2K FLASH for Bootloader; 2K EEPROM; 3 Timers Counters
and 5 Programmable Counter Array channels (for PWM, watch dog,
compare, capture); 24 TTL I/O lines; 8 A/D 10 bits;
RS 232 or TTL; CAN; 1 status
LED; configuration jumper; etc.
|
![](../MM_Type/i_foto/i_518.gif) |
GMM 518
grifo®
Mini Module AT89C51AC2
This grifo®
Mini Module has a 28 pin connector and it is based
on Atmel AT89C51AC2 CPU with 32K FLASH;
256 Byte RAM;1K ERAM; 2K FLASH for Bootloader; 2K EEPROM; 3 Timers
Counters and 5 Programmable Counter Array channels (for PWM,
watch dog, compare, capture); 24 TTL I/O lines; 8 A/D
10 bits; RS 232 or TTL; 1 status LED; configuration jumper; etc.
|
![](../MM_Type/i_foto/i_5115.gif) |
GMM 5115
grifo®
Mini Module 5115
grifo®
Mini Module has a 28 pin connector and it is based
on Atmel T89C5115 CPU with 16K FLASH; 256
Bytes RAM; 256 Bytes ERAM; 2K FLASH for Bootloader; 2K EEPROM;
3 Timer Counter and 2 Programmable Counter Array channels (for
PWM, compare, capture); 20 TTL I/O lines; 6 A/D 10
bit: RS 232 or TTL; 1 status LED; configuration
dip switch; etc.
|
![](../SOFT/FOTO/bascom_8051.jpg) |
FREE OF CHARGE
Theoretical/Practical Course
on
|
![](../MM_Type/i_foto/i_gmmtst3.gif) |
GMM TST3
grifo®
Mini Module Test 3
Low price card usefull for evaluating and test purpose
of 28 or 40 pin grifo®
Mini Modules type GMM 936, GMM AM08,
GMM AM32, GMM 876, etc...It provides: D9
connectors for a direct connections to 2 RS 232
lines; Buzzer; Connector for PonyProg;
Connector 6 pin for a direct connections to AVRISP
MK2; Connector 10 pin for a direct connections
to MP PIK/USB; Connector
6 pin for a direct connections to MPLAB®
ICD 2; 16 Key buttons; 2 lines LCD display; power
supply section with standard connector; push buttons and LEDs
for digital I/O signals management; etc.
|
MM
Type C P U - grifo® Mini Modules - A R M 7 Core |
![](../i_foto/i_lavor.gif) |
GMM ARM7
grifo®
Mini Module ARM7
grifo®
Mini Module has a 40 pin connector and it is based
on ARM7 CPU
|
MM
Type C P U - grifo® Mini Modules - A V R Core |
![](../MM_Type/i_foto/i_am128.gif) |
GMM AM128
grifo®
Mini Modulo ATmega128
grifo®
Mini Modulo da 40 pin basata sulla CPU Atmel ATmega128
con 128K FLASH; 4K SRAM; 4K EEPROM; 3 Timer Counter e
2 sezioni di Timer Counter ad alta funzionalita'; 7 PWM; 5 A/D;
RTC + 240 Bytes RAM, tamponati con batteria al Litio; 1 Comparatore;
I2C BUS; Master/Slave SPI Serial Interface; Interfaccia JTAG;
32 linee di I/O TTL; 2 RS 232 o TTL; 2 LED
di stato; ecc.
|
![](../MM_Type/i_foto/i_AM644.gif) |
GMM AM1284
grifo®
Mini Module ATmega1284P
grifo®
Mini Module has a 40 pin connector and it is based
on Atmel ATmega1284P CPU witch 128K FLASH; 16K
SRAM; 4K EEPROM; 3 Timer Counter and 2 Programmable Counter Array
channels; 4 PWM; 8 A/D; 1 Comparetor; RTC + Lithium battery +
64Kb FRAM; I2C BUS; Master/Slave SPI Serial Interface; JTAG Interface;
32 TTL I/O lines; 2 RS 232 or TTL; 2
status LED; etc.
|
![](../MM_Type/i_foto/i_AM644.gif) |
GMM AM644
grifo®
Mini Module ATmega644P
grifo®
Mini Module has a 40 pin connector and it is based
on Atmel ATmega644P CPU witch 64K FLASH; 4K SRAM;
2K EEPROM; 3 Timer Counter and 2 Programmable Counter Array channels;
4 PWM; 8 A/D; 1 Comparetor; RTC + Lithium battery + 64Kb FRAM;
I2C BUS; Master/Slave SPI Serial Interface; JTAG Interface; 32
TTL I/O lines; 2 RS 232 or TTL; 2 status
LED; etc.
|
![](../MM_Type/i_foto/i_32.gif) |
GMM AM32
grifo®
Mini Module ATmega32L
grifo®
Mini Module has a 40 pin connector and it is based
on Atmel ATmega32L CPU witch 32K FLASH; 2K SRAM;
1K EEPROM; 3 Timer Counter eand 2 Programmable Counter Array
channels; 4 PWM; 4 A/D; 1 Comparetor; RTC + 240 Bytes SRAM, backed
by Lithium battery; I2C BUS; Master/Slave SPI Serial Interface;
JTAG Interface; 32 TTL I/O lines; RS 232 or TTL;
2 status LED; ecc.
|
|
GMM AM328
grifo®
Mini Module ATmega328
grifo®
Mini Module has a 28 pin connector and it is based
on Atmel ATmega328 CPU with 32K FLASH; 2K SRAM;
1K EEPROM; 3 Timer Counter and 2 Programmable Counter Array channels;
6 PWM; 8 A/D; 1 Comparetor; I2C BUS; Master/Slave SPI Serial
Interface; 23 TTL I/O lines; RS 232 or TTL; 1
status LED; etc.
|
![](../MM_Type/i_foto/i_08.gif) |
GMM AM08
grifo®
Mini Module ATmega08L
grifo®
Mini Module has a 28 pin connector and it is based
on Atmel ATmega08L CPU with 8K FLASH; 1K SRAM;
512 Byte EEPROM; 3 Timer Counter and 2 Programmable Counter Array
channels; 3 PWM; 4 A/D; 1 Comparetor; I2C BUS; Master/Slave SPI
Serial Interface; 23 TTL I/O lines; RS 232 or TTL;
1 status LED; ecc.
|
![](../MM_Type/i_foto/i_gmmtst3.gif) |
GMM TST3
grifo®
Mini Module Test 3
Low price card usefull for evaluating and test purpose
of 28 or 40 pin grifo®
Mini Modules type GMM 936, GMM AM08,
GMM AM32, GMM 876, etc...It provides: D9
connectors for a direct connections to 2 RS 232
lines; Buzzer; Connector for PonyProg;
Connector 6 pin for a direct connections to AVRISP
MK2; Connector 10 pin for a direct connections
to MP PIK/USB; Connector
6 pin for a direct connections to MPLAB®
ICD 2; 16 Key buttons; 2 lines LCD display; power
supply section with standard connector; push buttons and LEDs
for digital I/O signals management; etc.
|
![](../PROG/HBI/i_foto/i_AVRISPmkII.jpg) |
AVRISP
MKII
Low-Cost ATMEL ISP Programmer
for Micros AVR.
USB Interface.
|
![wpe1.jpg (4608 bytes)](../SOFT/FOTO/bascom1.jpg) |
FREE OF CHARGE
Theoretical/Practical Course
on
|
MM
Type C P U - grifo® Mini Modules - PICCore |
![](../MM_Type/i_foto/i_gmm4620.gif) |
GMM 4620
grifo®
Mini Module PIC18F4620
grifo®
Mini Module has a 40 pin connector and it is based
on Microchip PIC18F4620 CPU witch 64K FLASH; 4K
SRAM; 1K EEPROM; 3 Timer Counter ; 2 PWM; 5 A/D; 33 TTL
I/O lines;1 Comparetor; RTC + 240 Bytes SRAM, backed by Lithium
battery; I2C BUS; Master/Slave SPI; RS 232 or TTL; 2 status
LED; ecc.
|
![](../MM_Type/i_foto/i_876.gif) |
GMM 876
grifo®
Mini Module 876
grifo®
Mini Module has a 28 pin connector and it is based
on Microchip PIC16F876A CPU witch 14,3K FLASH;
368 byte SRAM; 256 byte EEPROM; 2 Timer Counter ; 2 PWM; 4 A/D;
22 TTL I/O lines;1 Comparetor; I2C BUS; Master/Slave
SPI; RS 232 or TTL; 1 status LED; ecc.
|
![](../MM_Type/i_foto/i_876.gif) |
GMM 886
grifo®
Mini Module PIC16F886
grifo®
Mini Module has a 28 pin connector and it is based
on Microchip PIC16F886 CPU with 14,3K FLASH; 368
byte SRAM; 256 byte EEPROM; 4 Timer Counter ; 2 PWM; 11 A/D;
Master/Slave SPI; In-Circuit Serial ProgrammingTM (ICSPTM) via
Two Pins; 22 TTL I/O lines; 2-8 Comparetor; I2C
BUS; Master/Slave SPI; RS 232 or TTL; 1 status LED;
ecc.
|
![](../MM_Type/i_foto/i_gmmtst3.gif) |
GMM TST3
grifo®
Mini Module Test 3
Low price card usefull for evaluating and test purpose
of 28 or 40 pin grifo®
Mini Modules type GMM 936, GMM AM08,
GMM AM32, GMM 876, etc...It provides: D9
connectors for a direct connections to 2 RS 232
lines; Buzzer; Connector for PonyProg;
Connector 6 pin for a direct connections to AVRISP
MK2; Connector 10 pin for a direct connections
to MP PIK/USB; Connector
6 pin for a direct connections to MPLAB®
ICD 2; 16 Key buttons; 2 lines LCD display; power
supply section with standard connector; push buttons and LEDs
for digital I/O signals management; etc.
|
![](../MM_Type/i_foto/i_PG_PIC.gif) |
GMMPIC-PG
grifo®
Mini Module PIC-Programmer
Low price card usefull for programmer 28 or
40 pin grifo®
Mini Modules type GMM 876, GMM 4620,
CANPIC, etc. It provides: ZIF 40 pin socket; D9
connectors for a direct connections to RS 232 line; Connectors
RJ12 for MPLAB®;
Connectors 10 pin for a direct connections to MP PIK+; power supply section with
standard connector; 2 LEDs; etc.
|
Q
T P - Quick Terminal Panel |
![](../QTP/i_foto/i_qtp12tr.gif) |
QTP 12
Quick Terminal Panels 12 keys; 1 LED;
Graphic and Alphanumeric Display
20x2; Buzzer; Serial Line RS232, RS422/485, C. Loop; CAN; Power Supply.
|
![](../QTP/i_foto/i_qtp12H_4.gif) |
QTP 12H
Without keyboard; Graphic
and Alphanumeric Display 20x2; Buzzer; Serial Line RS232,
RS422/485, C. Loop; CAN;
Power Supply.
|
![](../QTP/i_foto/i_qtp16Big_LFR.gif) |
QTP 16Big
QTP 16 Big
- 3 Relay
Quick Terminal Panels Big 16 keys; 5
LED; Alphanumeric Display 20x4; 3 Relay; Buzzer; Serial
Line RS232, RS422/485, C. Loop; CAN;
Power Supply.
|
![](../QTP/i_foto/i_qtp16BH_LFR.gif) |
QTP 12Big-H
QTP 16 Big
- 3 Relay
Without keyboard; Alphanumeric Display
20x4; 3 Relay; Buzzer; Serial Line RS232, RS422/485, C.
Loop; CAN; Power Supply.
|