' ********************************************************************** ' ** Program name: AD4ch51.BAS - Version : 1.2 - 05 June 2000 ** ' ** Compiler : BASCOM 8051 DEMO, (IDE V.2.0.0.0, LIB V.2.0) ** ' ** Board : K51-AVR ** ' ** Firm: grifo(r) ITALIAN TECHNOLOGY ** ' ** Via Dell' Artigiano 8/6 40016 San Giorgio di Piano (BO) ** ' ** Tel.+39 051 892 052 Fax +39 051 893 661 ** ' ** http://www.grifo.com http://www.grifo.it ** ' ** sales@grifo.it tech@grifo.it grifo@grifo.it ** ' ** ** ' ** Written by: Adriano Pedrielli ** ' ********************************************************************** ' ' This program monitors one analogic channel out of four, managed by ' IC12 (PCF8591), visualization of the channel is in hexadecimal format, ' through T1 the channel to convert is selected: ' Whenever a key is pressed, an acoustic signal is emitted. ' Display DY1 shows the channel to convert, while displays DY3 and DY4 ' show the converted value in HEX. ' ' Before compiling set in menu Option/Compiler/Misc: Byte End 5F. ' '*********************************************************************** ' '******************* Compilatore directives **************************** ' $regfile = "REG51.DAT" ' 8xc51 registers list '$regfile = "89c2051.DAT" ' 89c2051 registers list $romstart = &H0 ' code starting address $crystal = 11059200 ' CPU clock frequence Config Debounce = 50 ' Time to wait before considering ' a key as pressed ' E.g.: 10= 10ms, 50= 50ms ' ' *************** List PINs for use with 89c1051/2051/4051 ********************* Config Sda = P1.7 ' Pin 19 DATA signal for I2CBUS Config Scl = P1.6 ' Pin 18 Clock signal for I2CBUS T1 Alias P1.5 ' Pin 17 connected to key T1 T2 Alias P1.4 ' Pin 16 connected to key T2 T3 Alias P1.3 ' Pin 15 connected to key T3 Buz Alias P3.5 ' Pin 9 connected to Buzzer ' ' *************************** List PINs for use with 8xc51 ********************* 'Config Sda = P3.6 ' Pin 16 DATA signal for I2CBUS 'Config Scl = P3.7 ' Pin 17 Clock signal for I2CBUS 'T1 Alias P1.0 ' Pin 1 connected to key T1 'T2 Alias P1.1 ' Pin 2 connected to key T2 'T3 Alias P1.2 ' Pin 3 connected to key T3 'Buz Alias P3.5 ' Pin 15 connected to Buzzer ' '********************** Constants decaration **************************** ' Dim Saa1064 As Const &H38 ' Slave address SAA1064 Dim Wsaa1064 As Const &H70 ' Slave address SAA1064 in Write Dim Rsaa1064 As Const &H71 ' Slave address SAA1064 in Read ' ******************** List addresses of Saa1064 *********************** Dim Ctb As Const 0 ' Address Control byte Dim Dig1 As Const 1 ' Address Digit 1 Dim Dig2 As Const 2 ' Address Digit 2 Dim Dig3 As Const 3 ' Address Digit 3 Dim Dig4 As Const 4 ' Address Digit 4 ' ' ********************************************************************** ' Dim Pcf8591 As Const &H48 ' Slave address PCF8591 Dim Wpcf8591 As Const &H90 ' Slave address PCF8591 in Write Dim Rpcf8591 As Const &H91 ' Slave address PCF8591 in Read ' '********************** Variables declaration ************************** ' Dim Dig As Byte ' value of a digit Dim Cifh As Byte ' 4 bit high in HEX for figure Dim Cifl As Byte ' 4 bit low in HEX for figure Dim N1 As Byte ' number 1 byte for DY3 and DY4 Dim Valore As Byte ' numbero to convert Dim C As Byte ' indicates the channel to convert ' '********************* Procedures declaration ************************** ' Declare Sub Iniz ' Peripherals initialization Declare Sub Ad(c As Byte , Valore As Byte) ' A/D converter management Declare Sub Cifre (valore As Byte , Cifh As Byte , Cifl As Byte ) ' converts a number in 2 HEX figures Declare Sub Digit (dig As Byte ) ' Converts a number in range 0-F in 7 segments Declare Sub Vis_num (n1 As Byte) ' Shows a byte in HEX ' '*************************** Main program ******************************** ' Main: ' Delay for signals settling Waitms 1 Call Iniz ' initializations C = 0 Valore = 0 Do Call Ad(c , Valore) Call Vis_num(valore) ' show the byte in HEX Debounce T1 , 0 , Incrementa , Sub Loop Incrementa: Buz = 0 ' turn on the buzzer Waitms 50 ' delay If C < 3 Then Incr C Else C = 0 End If Buz = 1 ' turn off the buzzer Return End ' '**************************** Program end ******************************* ' ' '**************************** Procedures ******************************** ' ' ********************** Peripherals initialization ******************** ' This procedure performs all the system initializations. ' Parameters: ' Input : nothing ' Output : nothing ' ************************************************************************ ' ' Sub Iniz ' Peripherals initialization Do I2creceive Rsaa1064 , Valore ' read status register Loop Until Valore = 0 ' wait for SAA1064 turned on I2cstart ' Start sequence for I2CBUS I2cwbyte Wsaa1064 ' Comunicate the Slave address I2cwbyte Ctb ' Point to control register I2cwbyte &B00100111 ' bit0 =1 dynamic mode ' bit1 =1 digit 1+3 not blanked ' bit2 =1 digit 2+4 not blanked ' bit3 =0 no test segment ' bit4 =0 no 3mA segment current ' bit5 =1 6mA segment current ' bit6 =0 no 12mA segment current ' bit7 =0 indifferent I2cwbyte 0 ' sets DY1 off I2cwbyte 0 ' sets DY2 off I2cwbyte 0 ' sets DY3 off I2cwbyte 0 ' sets DY4 off I2cstop End Sub ' ' ******************** A/D converter management **************************** ' QThis procedure allows to perform an analogic conversion through one of the ' four channels available on IC2 (PCF8591). ' Parameters: ' Input : C as byte, indicates the channel to convert (0...3) ' Output : Valore as byte, value in the range from 0 to 255 (0v...+Vref) ' ************************************************************************ ' Sub Ad(ch As Byte , Valore As Byte) ' A/D converter management C = C And &H03 ' keep Bit 0 and Bit 1 I2csend Wpcf8591 , C ' point to the channel to convert I2creceive Rpcf8591 , Valore ' read previous conversion I2creceive Rpcf8591 , Valore ' read current conversion End Sub ' ' ***************** Converts a figure in range from 0 to F in 7 segments *********** ' This procedure converts a figure in range from 0 to F in 7 segments format, if ' value is greater than F the display is off. ' Parameters: ' Input : dig as byte, value in the range from 0 to F ' Outout : dig as byte, value in 7 segments format. ' ************************************************************************ ' Sub Digit (dig As Byte ) ' Converts a number in range 0-F in 7 segments If Dig < 16 Then ' number is lower than 16 Dig = Lookup(dig , Tab_7seg) ' read value in table Else Dig = 0 ' if = 16 or greater reset End If End Sub ' ' This procedure converts 1 byte in range from 0 to 255 in two 4 bits hexadecimal ' figures. ' Parameters: ' Input : Valore as byte, value in the range from 0 to 255 ' Output : Cifh as byte, figure of high nibble ' Cifl as byte, figure of low nibble ' ************************************************************************ ' Sub Cifre (valore As Byte , Cifh As Byte , Cifl As Byte ) ' converts a number in two HEX figures Cifh = Valore And &HF0 ' mask 4 high bits Cifh = Cifh / 16 ' shift to low the 4 high bits Cifl = Valore And &H0F ' mask the 4 low bits End Sub ' ' *********************** Visualizes a byte in HEX ********************** ' The first display visualizes the number of the channel being converted, ' the second display is off. ' This procedure allows to show a byte in hexadecimal format ' in the two displays on the right. E.g.: 255= FFH, 32= 20H etc. ' Parameters: ' Input : N1 as byte, number to visualize in HEX ' Output : nothing ' ************************************************************************ ' Sub Vis_num (n1 As Byte) ' visualizes a byte in HEX I2cstart ' START sequence I2cwbyte Wsaa1064 ' slave address I2cwbyte Dig1 ' point to display 1 (DY1) Call Digit(c) ' convert the decines figure in 7 segments I2cwbyte Dig ' output to the first display DY1 I2cwbyte 0 ' output to the second display DY2 Call Cifre(n1 , Cifh , Cifl) ' convert the numbero in 2 HEX figures Call Digit(cifh) ' convert figure in HEX in 7 segments I2cwbyte Dig ' output to display DY3 Call Digit(cifl) ' convert figure in HEX in 7 segments I2cwbyte Dig ' output to display DY4 I2cstop ' stop sequence End Sub ' ' ************* Conversion table for 7 segments figure in the range from 0 to 15 ******* Tab_7seg: ' num. 0 1 2 3 4 5 6 7 8 9 Data &H3F , &H06 , &H5B , &H4F , &H66 , &H6D , &H7D , &H07 , &H7F , &H6F ' num. A b C d E F Data &H77 , &H7C , &H39 , &H5E , &H79 , &H71 ' ************************************************************************** '