GPC® T94

General Purpose Controller; Transistors

9 Inputs; 4 Outputs

Manual for Telecontrol program on GPC® x94

GPC® T94 English Tech. Manual PDF format.

Ver.5.40 - Rel. 24 July 2001.

The GPC® T94 belongs to the CPUs M Serie 22,5x82x90 mm. size, and it is a powerful control Low-Cost module capable of operating in stand-alone mode or as an intelligent peripheral, and/or remoted, in a wider Telecontrol or aquisition network. Low-Cost solution fot QTP display with QTP-03, QTP-4x6, etc.

The GPC® T94 module is secured in a plastic mount for connection to Omega rails DIN 46277-1 and DIN 46277-2, thereby dispensing with the need of rack and allowing a less costly mounting direct to the electrical control panel. The facility in the performance can be carried on thanks to a wide range of software developement tools with evoluted language which, in an efficient and friendly environment, allow to work at the best by using a standard PC. For example with BASCOM LT and SIM2051 it is possible to generate applications in really fast time and with minimal investments.

The GPC® T94 is available with Telecontrol firmware already programmed on -board. In this case by using the ALB communication protocole (Abaco® Link BUS) wuth One Wire® sensors, the GPC® T94 can be used as intelligent module in stand-alone mode or in network mode through a normal serial line. It is so possible, to realize applications with few I/O which are driven by a remote PC.

• - Intelligent Abaco® BLOCK module, M Serie. 22,5 x 82 x 90 mm size.
• - Plastic mount for connection to DIN 46277-1 and DIN 46277-2 Omega Rails.
• - 12÷24 MHz 89C2051, or 89C4051, CPU.
• - 4K bytes FLASH and 128 bytes RAM.
• - Code compatible with 51 family µP.
• - Real Time Clock with 256 bytes of internal RAM.
• - Back-up circuitery for RAM and RTC through LITHIUM battery.
• - 1K bytes serial EEPROM.
• - 9 Optocoupled Input.
• - Optocoupled external INT line.
• - 4 Optocoupled Darlington outputs.
• - LEDs to visualize I/O status lines.
• - All I/O connections are available on easy quick terminal connectors.
• - 16 bits Timer-Counter registers.
• - 1 line 11 bits A/D Converter with analog input range:
  • 0÷10Vdc and conversion time = 60 ms.
  • 2 TTL I/O lines. It is so possible to manage two different, end indipendents, 1-Wire® lines. Direct manage for 2 Dallas DS18S20 Temperature Sensors, Memories or for driving Dallas iButtom™, etc.
• - Serial line in:
  • RS232, RS422, RS485 or Current Loop.
• - Facility of operation in Idle or Power down mode.
• - Built-in Switching power supply with high performance.
  • +24 Vdc for optocoupled power supply.
  • 5÷40 Vdc or 10÷24 Vdc for on board logic.
• - On-board protection aganist voltage peaks by TransZorb.
• - Wide range of Developping Software Tools such as: C Compiler, Abaco® Link BUS, Assembler, BASIC Compiler BASCOM LT, BASCOM 8051, HTC-51, LadderWORK, etc.

BASCOM-8051

W95/NT 8051-BASIC Compiler

BASCOM-8051© is a Windows BASIC COMPILER for the 8051 family It is designed to run on W95/NT and has all the features of BASCOM LT. In addition it has full support for arrays and the single floating point type.

BASCOM-8051 - DEMO [11 October 2007 Rel. 2.0.14.0] - Length 6,3 MB - DOWNLOAD

A new version 2.0.14.0 is released of BASCOM-8051.
There is a new Demo as well. This demo can create files of 4 KB.

You can download the DEMO from the Download section.
Customers that have BASCOM-8051 can download from the register.
You can not turn a demo into a full version!

µ C / 5 1

ANSI C Compiler for 8051

Develop high quality software for any 8051 in ANSI C. µC/51 comes with an incredible optimizing compiler, you can even write software in ANSI C on 8051's with 1kB of code memory! µC/51 is absolutely complete: user friendly multi file Editor, Compiler, Assembler, Downloader, Source Level Debugger. You will not need anything else.

Download the Demo (uc/51_v1.20.05 - 7,7 MByte, UK documentation included)

F R E E - 8KB LIMITED DEMO

LadderWORK

The LadderWORK Integrated Development Enviroment (IDE)

The picture below, represents the apperance of the program LadderWORK on your computer. LadderWORK has an integrated enviroment feature, allowing you to draw schematics, compile programs and upload code to PLC always working on the same window. The integrated enviroments are composed by several parts described below. 

Converter

89C51/AT89C2051

• Adaptor for T-EMU52 and others MCS51 emulators
• Converts pins of AT89C2051 to 89C51/89C52
• Includes analog comparator
• Availability of disconnecting P1.0/20-P1.0/40 and P1.1/20-P1.1/40

EXPS 2 The EXPS 2 module is a complete, low cost, switching power supply with extremely reduced dimension, that can be used in conjunction with grifo® cards as GPC® R94, GPC® T94, GPC® R63, GPC® T63, GPC® R168, GPC® T168, QTP 12/R84, etc.

A C C E S S O R I E S
	CKS AMP 8 Connector KIT Set, 8 pins 8 Female pins + AMP plastic housing for QTP_03, etc..
	AMP8 Cable AMP Cable Connector, 8 pins 1 m cable with 8 pins female AMP connector for QTP_03, etc..

Page up-dated at April 18, 2010

Home Cards Categorical Index CPU Table