' **********************************************************************
' ** Program name: S1DEB7.BAS -  Version : 1.1   -   03  June  1999   **
' ** Compiler : BASCOM LT, (IDE V.1.20, LIB V.1.27)                   **
' ** Board : GPC(r) 324 + ETI 324                                     **
' ** Firm:   grifo(r) ITALIAN TECHNOLOGY                              **
' ** Via Dell' Artigiano 8/6          40016 San Giorgio di Piano (BO) **
' ** Tel.+39 051 892 052     Fax +39 051 893 661                      **
' ** http://www.grifo.com    http://www.grifo.it                      **
' ** sales@grifo.it          tech@grifo.it          grifo@grifo.it    **
' **                                                                  **
' ** Written by:  Graziano Gaiba                                      **
' **********************************************************************
'
' This program shifts the lighting of a LED to one direction or the other
' according to the status of jumper 1. If jumper 1 is connected shifts from
' red LEDs to the others.
' To address correctly the ETI 324 board on ABACO(r) I/O Bus, you should
' configure the board to match the hex 80 address, to do this switch to OFF
' the switches from 1 to 4, switch to ON switch 5.
' To achieve the visualization of the lines, you should connect the CN3
' connector of GPC(r) 324 board to the CN15 connector of DEB(r) 01 board by
' a 20-pin flat cable.
'
'************************ Compiler Directives  *******************************
'
$romstart = &H8050                 ' start address of machine code
$ramstart = &HD000                 ' start address of data area
$ramsize = &H2800                  ' 10k of data area
$crystal = 22118400                ' clock of microcontroller
$baud = 19200                      ' RS-232 baud rate
$large                             ' 16 bit addressing mode
'
'************************** Constant declarations ****************************
'
Dim Pda As Const &HFF80            ' port A data register 
Dim Pdb As Const &HFF81            ' port B data register
Dim Pdc As Const &HFF82            ' port C data register
Dim Cnt As Const &HFF83            ' control register 
Dim Rundebug As Const &HFFF9       ' run/debug register
'
'************************** Variable declarations ****************************
'
Dim Shifter As Byte                ' Lighting shifter
Dim J1 As Byte                     ' Stores status of jumper 1
Dim Porta As Bit                   ' If 1 selects port A, else selects port C

Waitms 1                           ' Delay for signals settling

Out Cnt , &B10000010               ' Configures port B for output,
                                   ' port A e C	for input
'
'***************************** Main Program **********************************
'
Print "    Demonstration program 7 for section 1 of DEB(r) 01 board"
Print : Print "    Shifts the lighting of a LED to one direction (from red LEDs to others)"
Print "    if jumper 1 is connected, otherwise shifts to the other direction."
Print : Print "    Running..."
Print
Shifter = 1                        ' Starts with the LSB
Porta = 1                          ' Selects port A as first
Do
   Shifter = Not Shifter           ' Negates to drive LEDs in negated logic
   If Porta = 0 Then               ' If port C selected
      Out Pda , 255                ' Turns off port A LEDs
      Out Pdc , Shifter            ' Drives port C LEDs 
   Else
      Out Pda , Shifter            ' Drives port A LEDs
      Out Pdc , 255                ' Turns off port C LEDs
   End If
   Shifter = Not Shifter           ' Restores normal value for rotation
   Waitms 255                      ' Delay for few rotations per second
   J1 = Inp(rundebug)              ' Reads the run/debug register
   J1 = J1 And &B00000001          ' Isolates jumper 1
  If J1 = 0 Then                   ' If jumper 1 connected
      Rotate Shifter , Left        ' Shift from red LEDs to others
   Else
      Rotate Shifter , Right       ' Else does the opposite
   End If
   If Shifter = 0 Then             ' If rotation is over 
      Porta = Not Porta            ' Switch selection between port A and C
      If J1 = 0 Then               ' If jumper 1 connected
         Shifter = 1               ' Restart shifting from red LEDs to others
      Else
         Shifter = 128             'Else restart shifting to the other direction
      End If
   End If

Loop

End
'
'*************************** End of Main program *****************************
'